Changes from adopted text to adopted text

RemovedAnnex I – Part D – point 1 – point 1.3 – introductory part: 1.3. Transport, installation, maintenance, deconstruction, deinstallation and demolition rules, where applicable:

RemovedAnnex I – Part D – point 1 – point 1.3 – point a – introductory part: (a) Safety during transport, installation, deinstallation, maintenance, deconstruction and demolition:

RemovedAnnex I – Part D – point 1 – point 1.3 – point c – point ii: (ii) the type and frequency of inspections and maintenance required for safety and durability reasons and, where appropriate, the parts subject to wear and the criteria for replacement;

RemovedAnnex I – Part D – point 1 – point 1.6 – paragraph 1 a (new): Where available, information on the performance of the product as measured in terms of its inherent product environmental requirements.

RemovedAnnex II – point 2 – point a: (a) the manufacturer’s products registration(s) in EU databases and to his own product presentation website;

RemovedAnnex II – point 3 – point h: (h) social media contact details, where available;

RemovedAnnex II – point 4 – point h: (h) social media contact details, where available;

RemovedAnnex II – point 5 – point h: (h) social media contact details, where available.

RemovedAnnex II – point 6 – point h: (h) social media contact details, where available.

RemovedAnnex II – point 11 – point a: (a) the list of essential characteristics, as determined in the harmonised technical specification or European Assessment Document for the respective product category for which a performance is declared. When no performance is declared for one essential characteristic, its name can still be listed and the place where the performance could be given remains empty.

RemovedAnnex III – title: Procedure concerning a European Technical Assessment

RemovedAnnex III – point 1 – point c: (c) In the absence of a request for a European Technical Assessment, when the Commission initiates the development of a European Assessment Document, it shall deliver to the organisation of TABs a technical file describing the product, its use and details of the factory production control to become applicable. The TAB responsible for developing the EAD shall be nominated by the organisation of TABs.

RemovedAnnex III – point 1 – point c a (new): (ca) In the absence of a request for a European Technical Assessment, the organisation of TABs may initiate the development of a European Assessment Document. In this case, it shall deliver to the working group responsible for the development of the EAD a technical file describing the product, its use and the details of the factory production control which will be applicable. The TAB responsible for chairing the working group for developing the EAD shall be nominated by the organisation of TABs.

RemovedAnnex III – point 3: deleted / (deleted)

RemovedAnnex III – point 4: deleted / (deleted)

RemovedAnnex III – point 5: deleted / (deleted)

RemovedAnnex III – point 6: deleted / (deleted)

RemovedAnnex III – point 7: deleted / (deleted) / (deleted)

RemovedAnnex III – point 8: deleted / (deleted) / (deleted) / (deleted) / (deleted) / (deleted) / (deleted) / (deleted) / (deleted)

RemovedAnnex III – point 9: deleted / (deleted)

RemovedAnnex III a (new): Annex III a / Procedure for adopting a European Assessment Document / 1. Work programme / In the cases foreseen by points 1(a) and 1(b) of Annex III, after agreement with the manufacturer and the Group respectively, the organisation of TABs shall inform the Commission of the work programme for drawing up the European Assessment Document and the schedule for its execution, indicating the assessment programme. This communication shall take place within three months of receipt of the request for a European Technical Assessment by a TAB, which shall initiate the procedure as laid down in points 1(a) and 1(b) of Annex III. / In the case provided for by point 1(c) of Annex III, the organisation of TABs shall submit to the Commission the work programme for drawing up the European Assessment Document with the same content and within the same deadline as indicated in the previous subparagraph. The Commission shall then communicate to the organisation of TABs within 30 working days its observations on the work programme. The responsible TAB or the organisation of TABs, respectively, after having been given the opportunity to comment, shall amend the work programme accordingly. / In the case foreseen in point 1(d) of Annex III, the organisation of TABs shall inform the Commission of the work programme for drawing up the European Assessment Document and the schedule for its execution, indicating the assessment programme. / 2. The draft European Assessment Document / The organisation of T…

RemovedAnnex V – paragraph 1: The manufacturer shall correctly determine the product type pursuant to Article 3, point 31, and the corresponding product category on the basis of the applicable harmonised technical specification. Where a notified body is involved in assessment and verification, the notified body shall verify these determinations.

RemovedAnnex V – point 1 – point b – introductory part: (b) The notified body shall issue the certificate of constancy of performance and of conformity on the basis of:

RemovedAnnex V – point 1 – point b – point ii: (ii) an assessment of the performance of the product on the basis of type testing (including sampling of the item(s) to be taken as representative of the type), type calculation or tabulated values or documentation describing the product and, in all these cases, review of the documentation of the product;

RemovedAnnex V – point 1 – point c: (c) The notified body shall provide continuous surveillance, assessment and evaluation of factory production control.

RemovedAnnex V – point 2 – point b – introductory part: (b) The notified body shall issue the certificate of constancy of performance and of conformity on the basis of:

RemovedAnnex V – point 2 – point c: (c) The notified body shall provide continuous surveillance, assessment and evaluation of factory production control.

RemovedAnnex V – point 3 – point c: (c) The notified body shall provide continuous surveillance, assessment and evaluation of factory production control.

RemovedAnnex V – point 5 – point a – point i: deleted

RemovedAnnex V – point 5 – point b – point i: (i) an assessment of the performance on the basis of testing performed by a notified testing laboratory (based on sampling carried out by the manufacturer), calculation, tabulated values or descriptive documentation of the construction product;

RemovedAnnex V – point 5 – point b – point ii: (ii) confirmation of the correct determination of the product type and of the product category.

RemovedAnnex V – point 7 – point a – introductory part: (a) In the case of systems 1+, 1 and 2+, inspection of the manufacturing plant shall cover the entire technical part of the plant, at least with regard to the following element, which shall ensure a continuous orderly manufacturing process:

RemovedAnnex V – point 7 – point a – point i: (i) the factory production control specifying the measures and frequencies foreseen to ensure constancy of performance, including the critical to performance parameters;

RemovedAnnex V – point 7 – point a – point ii: deleted

RemovedAnnex V – point 7 – point a – point iii: deleted

RemovedAnnex V – point 7 – point b: (b) Factory production control shall cover the process from receipt of the raw materials and components to the dispatch of the product once the production has started (‘gate to gate’ approach) and include as a minimum the critical to performance parameters. In the case of systems 1+, 1 and 2+, the notified body shall assess whether this process is designed and optimised in view of the goal that the products conform with the product type and therefore reach the performances declared in the declaration of performance and are compliant with the requirements set out in or under this Regulation.

RemovedAnnex V – point 7 – point d: (d) In the case of system 3+, verification shall consist of the verification of all calculations and input data. In that context, the notified body shall verify whether the applicable rules on modelling and calculation laid down in the applicable harmonised technical specification or methodology provided by the Commission are followed and whether the calculation model and input data reflect the production process. In case a verified IT tool or one provided by the Commission is used, the verification shall focus on the correct use of the tool. Where secondary data is used, the notified body shall check whether the correct data sets, prescribed by applicable product specific calculation rules contained in the applicable harmonised technical specification or the methodology provided by the Commission, are used. Where company-specific data is used, the reliability of that data shall be verified. To that end, the notified body may undertake an audit of the manufacturing plant to which the data refer, and shall examine documentation to verify the reliability of the data.

RemovedAnnex V – point 7 – point f: (f) Where, in the case of system 1+, 1 , 2+ or 3+, there is evidence that the manufacturer has not performed his task properly or the product performances do not comply with the declared performances, the notified body shall refuse issuing a certificate for at least one year or withdraw the certificate whilst permitting issuing a new one only after the deficiencies have been remedied.